Mechanical teardown

18 V cordless drill/driver (generic, brushed)

A clamshell tool that turns battery energy into controlled torque at the chuck: motor, two-speed planetary gearbox, slip clutch, keyless chuck, trigger speed control.
Power toolUnbranded mid-range exampleillustrative$79.00300,000 / yr (assumed)
50
parts (27 line items)
28
theoretical minimum parts
24.4 %
DFA index (best practice > 25 %)
344 s
manual assembly time
$23.09
should-cost, 29 % of price
7.2/10
repairability

01What was examined

02Requirements and function structure

User needEngineering metricHow the design meets it
Drive 75 mm wood screws without stallingMax torque >= 40 N m (low gear)550-size motor x two-stage planetary (about 1:50) x clutch at max setting
Do not strip small screwsClutch slips at 1-10 N m over 20 settingsSpring-loaded balls on the ring-gear face; clutch collar compresses the spring
Drill holes fastHigh gear no-load speed 1500 rpmShift ring locks the second-stage carrier to the ring gear (direct drive)
Survive a 2 m drop onto concreteNo housing crack, gearbox still alignedPA6-GF30 housing halves with ribbed bosses; TPE overmold on the grip
All-day useMass <= 1.4 kg without batteryPlastic ring gears and housing, aluminum is avoided
  • Store and switch energy P01, P02, P15
    • Accept battery pack P01, P14
    • Vary speed and direction P02, P03
  • Convert to torque at the bit
    • Electrical to mechanical P04
    • Reduce speed, raise torque (two speeds) P05, P06, P07, P08, P09
    • Limit torque P10, P11, P12
    • Hold the bit P13
  • Hold, protect and cool P01, P16, P17
    • Light the work P18

03Bill of materials

IDPartQtySubassemblyMaterialProcessMassCostNecessary?
F01Chuck retaining screw (left-hand thread)1Chucksteelpurchased2.0 g$0.02no
P13Keyless chuck, 13 mm1Chucksteelpurchased160 g$2.90yes
P10Clutch balls6Clutchsteelpurchased6.0 g$0.06yes
P11Clutch spring1Clutchspring steelwire forming6.0 g$0.05yes
P12Clutch collar with detent1ClutchPA66injection molding16 g$0.39yes
P02Trigger switch module with FWD/REV and PWM board1ElectricsPA66purchased45 g$3.80yes
P03Direction slider1ElectricsPOMinjection molding3.0 g$0.07yes
P14Battery terminal block1Electricsbrasspurchased14 g$0.70yes
P15Wire harness (motor, switch, terminals, LED)1Electricscopperpurchased18 g$0.60no
P18LED work light on flex1Electricscopperpurchased2.0 g$0.25yes
F02Gearbox to motor screws2Gearboxsteelpurchased3.0 g$0.03no
P05Gearbox housing / ring gear, stage 11GearboxPA66-GF30injection molding38 g$0.64yes
P06Planet gears, stage 13GearboxPOMinjection molding7.5 g$0.16yes
P07Planet carrier with sun, stage 1 to 21Gearboxsintered steelpowder metallurgy22 g$0.33yes
P08Planet gears, stage 23Gearboxsintered steelpowder metallurgy18 g$0.58yes
P09Shift ring (speed selector) with wire spring1GearboxPA66injection molding9.0 g$0.19yes
P20Spindle with carrier, stage 21Gearboxalloy steelcnc turning55 g$1.47yes
P21Spindle ball bearing1Gearboxsteelpurchased12 g$0.35yes
P22Thrust washers3Gearboxsteelstamping4.5 g$0.06no
F03Clamshell screws, Torx T10 security9Housingsteelpurchased14 g$0.18no
L01Rating label1HousingPPpurchased1.0 g$0.03no
P01Housing half, left (clamshell)1HousingPA6-GF30injection molding120 g$1.07yes
P16Housing half, right (clamshell)1HousingPA6-GF30injection molding118 g$1.06yes
P17Grip overmold (on both halves)1HousingTPEovermolding22 g$0.69no
P19Belt clip with screw1Housingspring steelstamping20 g$0.10yes
P04550-size brushed DC motor with fan1Motorsteelpurchased230 g$6.50yes
S01Solder joints, motor and switch leads4Motortinpurchased0.80 g$0.04no

04Materials and processes

Mass by material

steel 431 g (45 %)pa6-gf30 238 g (25 %)pa66 70 g (7 %)alloy steel 55 g (6 %)sintered steel 40 g (4 %)pa66-gf30 38 g (4 %)other 94 g (10 %)

Cost by process

purchased $15.46 (69 %)injection molding $3.58 (16 %)cnc turning $1.47 (7 %)powder metallurgy $0.91 (4 %)overmolding $0.69 (3 %)other $0.20 (1 %)

05Design for assembly

0DFA index %60

E = 3 × Nmin / T = 3 × 28 / 344 s = 24.4 %. Joints: drop in x17, screw x14, align x6, solder x4, hold down x3, snap x2, press x2, wire route x1, adhesive x1. 16 fasteners.

Assembly time by line item

F03 Clamshell screws, Torx T10 sec81 sS01 Solder joints, motor and switc42 sP10 Clutch balls27 sF02 Gearbox to motor screws18 sP08 Planet gears, stage 214 sP06 Planet gears, stage 114 sP22 Thrust washers14 sP15 Wire harness (motor, switch, t12 sL01 Rating label12 sP11 Clutch spring10 s

Parts that are not theoretically necessary

IDPartQtyTime
F03Clamshell screws, Torx T10 security981.0 s
S01Solder joints, motor and switch leads442.0 s
F02Gearbox to motor screws218.0 s
P22Thrust washers313.5 s
P15Wire harness (motor, switch, terminals, LED)112.5 s
L01Rating label111.5 s
F01Chuck retaining screw (left-hand thread)19.0 s
P17Grip overmold (on both halves)13.0 s

Boothroyd test: a part must stay separate only if it moves relative to the others, needs a different material, or must come apart for assembly or service.

06Should-cost

Parts $22.32 + assembly labour $0.76 = $23.09, 29 % of the $79.00 retail price. 8 of 27 line items make 80 % of parts cost.

P04 550-size brushed DC motor with$6.50P02 Trigger switch module with FWD$3.80P13 Keyless chuck, 13 mm$2.90P20 Spindle with carrier, stage 2$1.47P01 Housing half, left (clamshell)$1.07P16 Housing half, right (clamshell$1.06P14 Battery terminal block$0.70P17 Grip overmold (on both halves)$0.69P05 Gearbox housing / ring gear, s$0.64P15 Wire harness (motor, switch, t$0.60

Estimates from mass, indicative material prices, machine rates and amortised tooling (or given quotes). Use for ranking and comparison, not for quoting.

07Design decisions worth copying

Clamshell with lay-in architecture
Every internal module drops into the left half; the right half closes it all with 9 screws.
Assembly is top-down in one fixture with no flipping. The cost is that every repair starts by opening the whole tool.
Mixed-material gear train
Plastic ring gear and stage-1 planets, sintered steel stage 2.
Plastic where speed is high and torque is low; steel where torque is high. Noise drops too.
Clutch built into the ring gear
The stage-2 ring gear face carries the ball ramps; the collar only loads the spring.
No separate clutch housing, so fewer parts and a shorter nose.
Shift by locking the carrier
The shift ring slides to lock stage 2 to the housing (low) or to the carrier (high).
Two speeds from one extra part instead of a second gear set.

08Repairability

0score / 1010
Wear / failure partHeld byParts removed firstScore
Trigger switch module with FWD/REV and PWM boardhold down28.6
550-size brushed DC motor with fanalign27.2
Planet gears, stage 1drop in47.1
Planet gears, stage 2drop in47.1
Clutch ballsdrop in58.0
Keyless chuck, 13 mmscrew010.0

09Failure modes

APItemModeEffectCauseS/O/DRPNAction
HighStage-1 planet gears (POM)Teeth shear under stallTool spins but no outputRepeated stalls at max clutch setting heat the plastic7/4/6168PA66-GF or sintered stage-1 planets on the high-torque SKU; thermal derating in firmware
HighTrigger switchContact weldingTool runs without triggerInrush at stall with a fresh battery9/2/7126MOSFET switching with the mechanical contact only as a signal
MediumMotor brushesWear-outLoss of power, sparkingCommutator wear over about 60 h duty6/6/4144Brushless upgrade path; or brush access door
MediumHousing boss at frontCrack on dropGearbox misaligns, noiseThin boss wall at screw F03-16/3/472Add gussets; core out to uniform 2.2 mm wall
LowClutch springSet (loss of preload)Clutch slips early, settings driftSpring stressed near yield at max setting4/4/580Re-check spring index and max shear stress; shot peen

10Benchmark

ProductMotorMax torqueMass (no battery)Clamshell screwsGearbox stages
This toolBrushed 550~40 N m~1.1 kg9 (security Torx)2 planetary
Typical brushless mid-rangeBrushless outrunner~60 N m~1.0 kg6-8 (Torx)2 planetary
Typical budget 12 VBrushed 380~25 N m~0.8 kg7 (Phillips)1-2 planetary

11Redesign opportunities

OpportunityChangeImpactEffortSaving / unit (negative = adds cost)
Plug the motor inReplace the 4 solder joints with a keyed 2-pin connector on the motor end capCuts about 30 s of assembly, makes the motor a 2-minute swaplow$0.05
Mold the thrust washers awayAdd a bearing shoulder on the stage-1 carrier and a molded thrust face on the ring gearRemoves 3 small parts that fall out during servicelow$0.03
Fewer, standard clamshell screws plus front snap hooksTwo snap hooks at the nose, 6 screws in place of 9, standard T10Faster close-up, opens with a normal drivermed$0.04
Brushless motor and MOSFET switchingBrushless motor with the PWM board; the trigger becomes a sensorRemoves the top two wear modes and the welded-contact hazardhigh−$3.50

Cost-down moves together: $0.12 per unit (0.5 % of should-cost; savings can overlap). Upgrades that add cost: $3.50 per unit.

12Engineering verdict

A well-optimized clamshell: the gearbox and integrated clutch are lean, and plastic is used where it is safe. Assembly is dominated by the harness and the solder joints rather than by the mechanics, and repairability is held back by security screws and by soldered motor leads. Switching to plug-in motor leads and standard screws costs nothing and makes the motor and switch user-replaceable. Brushless is the real next product, not a cost-down.